JB/T 9162.9-1999 空心表柱 尺寸
作者:标准资料网 时间:2024-05-15 22:00:08 浏览:9544
来源:标准资料网
基本信息
标准名称: | 空心表柱 尺寸 |
英文名称: | Hollow upright post - Dimensions |
中标分类: |
机械 >>
工艺装备 >>
一般卡具 |
ICS分类: |
机械制造 >>
机床 >>
机床综合
|
替代情况: | ZB J44001.9-87 |
发布日期: | 1999-05-20 |
实施日期: | 2000-01-01 |
首发日期: | 1900-01-01 |
作废日期: | 1900-01-01 |
归口单位: | 机械科学研究院 |
出版日期: | 1900-01-01 |
页数: | 1 页 |
批文号: | 国机管[1999]282号 |
适用范围
JB/T 9162.9-1999
前言
没有内容
目录
没有内容
引用标准
没有内容
所属分类: 机械 工艺装备 一般卡具 机械制造 机床 机床综合
【英文标准名称】:HydraulicFluidPower-CylinderPorts-SAEStraightThreadO-RingandFour-BoltFlangePorts-ISOStraightThreadO-RingandFour-BoltFlangePorts-Heavy-DutyandLight-DutySquareHeadTieRodCylinders
【原文标准名称】:液压动力传动.气缸口.SAE直螺纹O形密封圈和四螺栓法兰口.ISO直螺纹O形密封圈和四螺栓法兰口.重载和轻载四方头长螺栓气缸
【标准号】:ANSI/(NFPA)T3.6.54R1-1997
【标准状态】:作废
【国别】:美国
【发布日期】:1997
【实施或试行日期】:
【发布单位】:美国国家标准学会(ANSI)
【起草单位】:
【标准类型】:()
【标准水平】:()
【中文主题词】:
【英文主题词】:
【摘要】:
【中国标准分类号】:J20
【国际标准分类号】:23_100_20
【页数】:
【正文语种】:英语
Product Code:SAE J1453
Title:Fitting--O-Ring Face Seal (Cancelled Jan 2009, Superseded by J1453/1, J1453/2, J1453/3)
Issuing Committee:Hydraulic Tube Fittings Committee
Scope:This SAE Standard covers material, dimensional, and performance requirements of steel O-ring face seal fittings for tubing and the O-ring face seal interface and nut portion of hose stem assemblies for nominal tube or hose diameters 6.35 mm (0.250 in) through 38.1 mm (1.500 in). These fittings are intended for general application and hydraulic systems on industrial equipment and commercial products, where elastomeric seals are acceptable to overcome leakage and variations in assembly procedures. These fittings are capable of providing leak-proof full flow connections in hydraulic systems operating from 95 kPa (28 in Hg) vacuum to working pressures shown in Table 1. Since many factors influence the pressure at which a hydraulic system will or will not perform satisfactorily, these values should not be construed as guaranteed minimums. For any application, it is recommended that sufficient testing be conducted and reviewed by both the user and manufacturer to assure that required performance levels will be safe. See Figure 1.The rated working pressure of a fluid conductor assembly using SAE J1453 hose stem connections or formed tube connection per Figure 32a, shall not exceed rated working pressure of the lowest rated component thereof.